Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
The article following next pertaining to A Step-by-Step Guide to Installing a Bathtub is amazingly engaging. Don't overlook it.
Installing a bathtub isn't precisely brain surgery, yet it does require strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably challenging project. If the old bathtub is conveniently available, the job can relocate speedily; if you have to open a wall surface to eliminate the old tub and also place the brand-new bathtub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and set in the new one. Make certain you have actually certified on your own for the work and are comfortable attempting it. Instead of hiring a professional to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This write-up will certainly assist you install a new bath tub in your washroom if you have already bought a brand-new bathtub as well as don't need to transform the setup of your previous water system pipes.
Your devices and also product checklist should consist of the following:
Getting ready for the Installation
To start with, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets system to prevent strain on the bath tub.
Fit the versatile tap adapters to the bottom of both taps making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome as a result of the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing substance.
Before proceeding to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, position the tub in the required position. The wooden boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the water supply and also examine all joints and new pipework for leaks and tighten them if necessary. Fill the bathtub and also inspect the overflow outlet as well as the typical outlet for leaks.
Lastly, repair the bath paneling as explained in the producer's instruction manual. Tiling as well as sealing around the bathtub ought to wait until the bathtub has been used at least when as this will certainly settle it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin ensuring that the washing machines are in place in between the tap and also the sink. Protect the faucet in place with the manufacturer given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous kind ought to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to fracture a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in problems with dampness as well as possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are offered in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to enable the activity experienced when the tub remains in use. The sealer can fracture relatively very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly available on the market. It is suggested to fit the floor tiles utilizing waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about A Step-by-Step Guide to Installing a Bathtub? Try to leave a review down the page. We'd be pleased to hear your thoughts about this post. We are looking forward that you come back again in the future. Please set aside a second to distribute this page if you enjoyed reading it. Thank-you for your time spent reading it.
Explore Report this page